2005-2009 Ford Mustang GT-500 Style Fiberglass Hood | VIS Racing
| |||
VIS Racing GT-500 Style Fiberglass Hood for 2005-2009 Ford MustangGive your 2005-2009 Ford Mustang an aggressive performance-inspired appearance with the VIS Racing GT-500 Style Fiberglass Hood. Inspired by the distinctive GT-500 design, this aftermarket hood adds bold styling while providing a cost-conscious alternative to a genuine carbon fiber hood. Constructed from high-quality fiberglass reinforced plastic (FRP), this hood is supplied with a primer finish and is ready for the necessary preparation and custom paint work. Its GT-500-inspired styling makes it a distinctive exterior upgrade for Mustang owners looking to personalize their vehicle. Key Features
Vehicle CompatibilityFits: 2005, 2006, 2007, 2008 and 2009 Ford Mustang two-door models. Important Fitment Notice: This is a GT-500-style aftermarket hood. It does NOT fit the actual Ford Mustang Shelby GT500 or other Shelby models. Verify your vehicle configuration before ordering. Product Specifications
Important Installation InformationThis hood is supplied unfinished and requires preparation before painting. Typical preparation may include sanding, filling, priming and paint work. Test-fit the hood before making any modifications or beginning paint preparation. Professional installation by an experienced body shop is strongly recommended. Modifications and adjustments may be necessary to achieve proper fitment, hood alignment and panel gaps. Factory hood hinges and latch hardware may be needed for installation. Hood pins are required for proper installation and safety. Do not reuse factory hood struts, shocks, dampers or springs. Excessive pressure from these components can cause damage to an aftermarket hood. VIS Racing identifies this product as intended for off-road use unless permitted by applicable local or state laws. Check your local regulations before use on public roads. Give Your Mustang a GT-500-Inspired LookUpgrade your 2005-2009 Ford Mustang with aggressive GT-500 styling and a paint-ready fiberglass hood from VIS Racing. Manufacturer: VIS Racing | Part Number: 05FDMUS2DGT5-010  Important When Receiving Freight: upon receiving the product(s) please be sure to inspect the item(s) for "freight damage". If there are signs of freight damage you must refuse the item due to damage then contact us immediately. Make sure to open and inspect all content(s) before signing [this includes removing the wrapping bubbles and plastics to physically inspect the item(s)]. This process usually takes about 5-10 minutes. It is the customer's responsibility to inspect the item thoroughly. If a customer fails to fully open up the box(es) and inspect their merchandise for damage, and signs the freight carrier's paperwork indicating that all merchandise was inspected (which is what is stated on all freight carriers paperwork), inspects their merchandise after the freight carrier leaves and then finds damage, or what is called "concealed damage", neither the freight carrier, nor BMC Extreme Customs will be responsible to replace or pay for repairs to the product. CargoEdge Insurance Coverage Due to the size of the hood, they are vulnerable to getting damaged. It’s a common mistake to confuse freight insurance with the liability insurance provided by carriers and freight forwarders. They are not the same at all. Typical carrier or forwarder liability is limited, in some cases to no more than $5.00 per lb of stolen, lost, or damaged cargo, and coverage contains many exclusions. For a typical hood which weighs less than 50lbs, that's only $250 plus freight. CargoEdge Insurance is powered and backed by UPS Capital and adds a piece of mind should your order arrive damaged or stolen. *DISCLAIMER: All aftermarket hoods sold are either for show or off-road use only. Professional installation & Hood pins are required! The buyer assumes the entire risk as to the quality of the aftermarket parts. In the event such parts prove defective following the purchase and installation, the buyer assumes the entire costs of any necessary servicing, repair, or replacement. Note: This is not a simple bolt on. We want all consumers to know that there will always be sanding, shaving, cutting, and/or filling prior to installing aftermarket parts. Also, the black primer finish must be sanded and other prep work will be required prior to painting. Some adjustments may be required to properly fit the hood. It is recommended that you oversize the four holes where the hinges join together. This will allow you to adjust your hood height and front to back spacing. Further adjusting of the fender alignment to hood can be accomplished by loosening the screws that hold the fender to the inner wheel well, and if necessary to place the shims or washers between the fender lip and inner fender well to adjust gap. | |||
