2011-2014 Ford Mustang Vertical Door Kit | VDI VDCFM11

2011-2014 Ford Mustang Vertical Door Conversion Kit

Vertical Doors, Inc. VDCFM11 is a vehicle-specific vertical door conversion kit designed for the 2011-2014 Ford Mustang. The kit retains the factory front doors while changing their movement so they open outward first and then raise vertically.

Also commonly called a Mustang Lambo door kit, scissor door kit, or vertical door kit, the VDCFM11 is designed specifically around the fifth-generation Ford Mustang S197 platform.

Give Your S197 Mustang the Lambo Door Look

The 2011-2014 Ford Mustang represents the later S197 generation, combining the Mustang's classic long-door proportions with a more aggressive exterior design and performance models such as the GT, Boss 302 and Shelby variants.

A vertical door conversion gives the Mustang a distinctive custom appearance by allowing the front doors to swing outward and then lift vertically.

The VDCFM11 Ford Mustang vertical door kit uses the vehicle's original front doors and vehicle-specific hinge assemblies rather than a universal weld-on conversion.

VDCFM11 Product Specifications

What's Included With the VDCFM11 Kit?

• One driver-side Vertical Doors, Inc. hinge assembly
• One passenger-side Vertical Doors, Inc. hinge assembly
• Two gas shocks
• Required mounting hardware
• Vehicle-specific installation instructions

The kit is designed to retain the Mustang's original front doors. The VDI hinge assemblies and gas shocks provide the hardware needed to change the doors to vertical operation.

How Does the Mustang Vertical Door Kit Work?

After installation, the front door initially opens outward like a conventional door. Once the door reaches the hinge system's stopping point, it can be raised vertically.

The included gas shocks assist with the upward movement. Correct installation and adjustment are important for proper door alignment, smooth operation and adequate clearance around the door, fender and surrounding body panels.

Installation Requirements

The VDCFM11 is designed around the Mustang's factory hinge area. While the vehicle-specific design provides dedicated mounting hardware, bolt-on does not mean modification-free.

Installation commonly requires careful body-panel removal, clearance work, wiring management, hinge adjustment and final door alignment.

Typical installation procedures may include:

• Removing the front fenders to access the factory hinge area
• Removing the door panels to access the door wiring
• Creating additional wiring slack where necessary
• Routing the wiring through the modified hinge area
• Cutting the factory wire boot in half for routing
• Non-visible inner-fender trimming for necessary clearance
• Installing and adjusting the VDI hinge assemblies
• Installing the gas shocks
• Final door alignment and clearance adjustment

The factory wires generally do not need to be cut; however, wiring must be properly routed and secured to prevent interference or damage during door operation.

Protect Your Factory Door Alignment

Before loosening or removing the original hinges, use 2-inch painter's tape to mark the factory door alignment. Place tape across the door and adjacent body panels at several reference points, including areas near the hinges and firewall. Draw matching alignment lines across the tape.

These reference marks can help restore the door to its original horizontal and vertical position during reassembly and adjustment.

If you are not experienced with automotive body-panel removal, door alignment, trimming, drilling or tapping where applicable, or wiring clearance, professional installation by a qualified automotive customization or body shop is recommended.

2011-2014 Mustang Fitment

The VDCFM11 is listed for the 2011-2014 Ford Mustang and is intended for the fifth-generation S197 Mustang platform.

Mustang configurations during these model years included models such as the V6, GT, Boss 302 and Shelby GT500. However, the trim name alone should not be used as the sole basis for fitment.

Confirm the exact model year, model, body style and door configuration before ordering.

Vehicles equipped with aftermarket fenders, widebody kits, custom bodywork, previous collision repair, replacement hinges or modifications around the hinge and fender area may require additional consideration before installation.

Coupe vs. Convertible Fitment

The 2011-2014 Mustang was offered in both coupe and convertible configurations. Because vertical door hardware is vehicle-specific, confirm the exact body style of your Mustang before ordering.

Do not assume that a kit for one Mustang body configuration automatically applies to another vehicle simply because both vehicles share the same generation or model-year range.

Before You Order

1. Confirm your Mustang is a 2011-2014 model.
2. Confirm the exact model year.
3. Confirm the vehicle is a 2-door Mustang.
4. Confirm whether your Mustang is a coupe or convertible.
5. Confirm the vehicle's S197 generation/platform.
6. Disclose aftermarket fenders or widebody components.
7. Disclose custom bodywork or previous collision repair.
8. Disclose replacement hinges or modifications near the hinge area.
9. Review current shipping and return policies before purchasing.

Frequently Asked Questions

Is the VDCFM11 a universal Lambo door kit?

No. The VDCFM11 is a vehicle-specific vertical door conversion kit designed for the listed 2011-2014 Ford Mustang application. It is not a universal weld-on hinge system.

What Mustang generation does VDCFM11 fit?

The VDCFM11 is listed for the 2011-2014 fifth-generation Ford Mustang, commonly referred to as the S197 platform.

Does the kit replace the factory doors?

No. The Mustang's original front doors are retained. The VDI hinge assemblies and gas shocks change the way the doors open.

Does installation require cutting or trimming?

Installation commonly requires non-visible clearance trimming, body-panel removal, wiring management, hinge adjustment and careful final door alignment.

Do I have to cut the factory wiring?

The factory wire boot is cut in half for routing, but the factory wires generally do not need to be cut. Proper wiring routing and clearance are important for safe and reliable door operation.

Will the doors still open normally?

The converted doors first open outward and then raise vertically once they reach the hinge system's stopping point. Proper installation and adjustment are required for correct operation.

Is professional installation recommended?

Professional installation is recommended if you are not experienced with automotive body-panel removal, door alignment, hinge installation, clearance trimming and wiring management.

What are Mustang Lambo doors?

"Lambo doors" is a common aftermarket term for doors that raise vertically rather than opening entirely outward. They are also commonly called vertical doors or scissor doors. The VDCFM11 provides this style of door movement for the listed 2011-2014 Mustang application.

Fitment Disclaimer: Vehicle model, trim, engine, package, generation and model-year information is provided to help identify the intended application. It does not guarantee compatibility with every individual vehicle. Aftermarket body components, widebody conversions, collision repairs, replacement hinges and other modifications may affect installation or fitment. Confirm the exact application before ordering when fitment is uncertain.